焊接控制器PY-C-1(PY-2K5B)
1、焊接電源:AC220V/AC380V ±10% 50/60Hz (出廠時設定電壓)2、控制電源:AC220V/AC380V ±10% 50/60Hz (出廠時設定電壓)3、控制方式:可控矽相位控制。4、焊接時序設定 1)預壓時間 (SQ):01~99CYC 2)緩升時間 (SU):00~99CYC 3)焊接I時間 (W1):00~99CYC 4)冷卻時間 (CT):00~99CYC 5)焊接II時間 (W2):00~99CYC 6)維持時間 (HO):00~99CYC 7)休止時間 (OF):00~99CYC 8)電流I (WC1):00~99% 9)電流II (WC2):00~99%5、外部輸入信號 1) 電源開/關:控制電源打開或關閉。注意:請在打開/關閉電源前先將[通電/檢查]開關撥至[檢查]位置。不規範的操作有可能導致可控矽損壞。 2) 起動信號:起動控制裝置。 3) 通電/檢查:開路時,只進行焊接時序的動作而不通電。 4) 調整/焊接:閉路時,只進行氣閥信號的檢測。 5) 單點/連續:開路時,進行單點焊接動作。 6) 保持:[起動信號]的保持或非保持。 7) 故障清除:微處理機重新起動。 8) 檢溫器:接續於可控矽和焊接變壓器內的溫度傳感器。6、外部輸出信號 1)焊接結束:維持時間結束時,輸出一個脈衝信號。 2)工作:[起動信號]開始到[維持時間]結束,該燈點亮。 3)焊接I:該燈點亮的時間為[焊接I]時間 4)焊接II:該燈點亮的時間為[焊接II]時間 5)故障:控制器內部和外部檢測信號有故障時該燈點亮。 6)加壓:電磁閥控制信號。標準為:DC24V輸出 7)可控矽觸發脈衝:可控矽的導通信號。7、環境溫度:0—50 ºC8、外形尺寸和重量: 324mm(H)X 90mm(W)X 355mm(D)X5.0Kg9、安裝尺寸: 309mm(H)X 250mm(W) 孔:Ø6.0
技術參數:讀卡類型:MIFARE ONE標準卡;工作頻率:13.56MHZ;發 卡 量:無限制;顯 示:8位數碼管顯示;費率設置:最小計費時間1秒,最小計費金額0.01元;工作電壓:DC12V,待機時耗1.6W,刷卡供水時功耗小于5W;外形尺寸:200mm×133mm×47mm;工作溫度:0~90℃;工作濕度:10%~90%;產品包裝:標準;重 量:360克;
ic卡水控機產品功能分類: 大眾型(放卡出水,拔卡斷水,正常消費,無限制) 免費限時限量型(每天免費使用時間的限制 。通過設置可以將不同級別人員設定為具有每日不同時間(或流量)免費使用水,但當天的核定使用量) 收費型限時限量(按正常費率收費,限制每日最大用水時間或流量,保障后來者有足夠熱水)
4、系統功能和特點 A級防水設計,獨特的卡槽無按鈕暫停模式以及顯示窗與機殼的連體設計讓防水做到性。水控機的使用環境非常潮濕,這是電子產品的天敵。防水設計的好壞成為水控機的穩定性的重要因素之一。卡誠sk66系列水控機是根據多年的銷售及應用經驗而設計開發出來的升級版產品。在防水方面做了的改良。
本產品采用智能IC卡一卡通技術;擁有國內首創功能:可以實現脫機(控水器不聯網,充值機不聯網)掛失并采集掛失卡中余額功能 以卡控制閥門開關,將卡放在感應區自動扣費出水,拿開自動斷水,停止計費。使用更方便,設計更加人性化; 人性放卡槽設計(解決浴室無處放卡問題); 防水防潮(尤其浴室潮氣嚴重)專用模具 8位LED顯示,可以顯示卡中余額、費率、以及單位扣費的剩余時間等信息; 系統使用的IC卡為PHILIPS公司的M1非接觸智能卡,充值卡上資源豐富,卡上IC芯片容量大,有16個扇區可分配使用 系統使用的充值機有電腦操作和鍵盤操作兩種,以便用戶根據需要進行選擇; 變人工收費為自助收費,實現收費自動統計,管理更科學,更現代; 全防水無接縫設計,產品具有更高穩定性、耐用性; 自動識別持卡人的合法性,根據卡內賬戶信息決定是否允許消費; 系統遇強磁干擾,非法開殼等惡意破壞行為時,控水器自動關斷閥門;
Lactate ScoutBIOSEN系列葡萄糖/乳酸分析儀以及CLAMP智能化葡萄糖鉗夾實驗系統之后,德國EKF診斷公司收購了SensLab公司。并發布了Lactate Scout血乳酸儀。Lactate Scout血乳酸儀采用乳酸氧化酶-電極法檢測人體血乳酸含量。\\\\r
Lactate Scout血乳酸儀采用Lactate Scout專用血乳酸試紙片,0.5uL血標本,在15秒秒內檢測人體血乳酸含量。Lactate Scout血乳酸儀可分步檢測血乳酸,特別適合運動員的血乳酸測定。同時,EKF診斷公司還發布了配套軟件,采用更直觀的圖形界面測量運動員血乳酸拐點水平。為制定科學的訓練方案提供依據。\\\\r
Lactate Scout血乳酸儀采用普通AAA電池即可使用,特別適合急診、ICU、體育運動隊快速血乳酸檢校 正 值:3~8%(由樣品濃度決定)結果存儲:250個測試結果,可與PC連接,需購買專用數據線安裝軟件中包括個體的訓練監控程序體 積:90×50×20mm重 量:約85.1g(帶電池)電 池:2節7號干電池產 地:德國試紙條:一盒550(一盒是24張)
BI20U-CK40-AN6X2-H1141 ;圖爾克接近開關;MK13-451EX0-T/230VACMK13-N-EX0/24VDCMK13-NF-EX0/24VDCMK13-P-EX0/24VDCMK13-PF-EX0/24VDCMK13-PN-EX0/24VDCMK13-R-EX0MK13-R-EX0/24VDCMK15-12EX0-PN/24VDCMK15-12EX0-PN/24VDC/K11 MK21-122EX0-RMK21-122-RMK21-122EX0-RIMK21-122-RIMK26-22-R/24VDCMK26-22-R/115VACMK26-22-R/230VACMK31-11EX0-LI/24VDCMK31-11-LI/24VDCMK31-11EX0-LU/24VDCMK31-11-LU/24VDCMK31-111-LI/24VDCMK31-111EX0-LI/24VDCMK31-111-LU/24VDCMK31-111EX0-LU/24VDCMK31-112EX0-LI/24VDCMK31-112-LI/24VDCMK31-112EX0-LU/24VDCMK31-112-LU/24VDCMK31-113EX0-LI/24VDCMK31-113EX0-LU/24VDCMK31-114EX0-LU/24VDCMK31-115EX0-LI/24VDC
![]() |
![]() |
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
|
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
|
WMC系列小載荷拉壓雙向力傳感器 | 查看詳細 | |||||||||||||||||||
![]() |
|
參考:
http://www.sensor99.com/dict/lvl3.asp?action=cs&BigClassID=232&productTypeID=232&page=1
自帶風機熱風器:LEISTER TYP Hotwind-S (9C1/9C3)技術規格:230V/3.7 KW ;380V/4 KW 溫度:650℃;620℃ 連續可調 20℃風量:600L/min;550 L/min 風機靜壓:200 Pa 出風口徑:Φ62 mm 外形尺寸:350 × 172 × 99 mm 總 重 量:3.2 kg (自帶風機) 特點:LEISTER TYP Hotwind-S熱風器超小型、自帶風機一體化設計;無碳刷電機,適于流水線24小時連續工作;特殊訂制可達900度高溫應用:LEISTER TYP Hotwind-S熱風器適用生產線加熱、烘干、熱收縮包裝。廣泛應用于包裝機械、干燥設備、食品滅菌包裝、橡膠塑料等行業,尤其是套標機上,如酒瓶、醋瓶和醬油瓶等瓶口的塑料收縮防偽套標。在纏繞管的生產干燥過程中也有應用。
美國道康寧(Dow corning) 732、734、736、737、738、739、744、748、780、LDC7091有機硅密封膠;CN-8603、CN-8605 室溫固化粘結膠;3140、LDC3140、3145、3165 RTV膠;SE9168、SE9184、SE9186、SE9176、SE9187L、 SE9189L 矽膠;SE4410、SE4420、SE4450 導熱硅膠;160、170 灌封膠;1-2577 防水油、1-2577 LOW VOC 線路板防潮絕緣油;1-2620、3-1753、3-1953、3-1744、3-1944、3-1765、3-1965 絕緣披覆膠;340、CN-8880、SC102、TC-5021、TC-5022、TC-5026、TC-5121導熱硅脂、Q1-9226 散熱絕緣膠
特性: | ||||||||||||||||||||
每次濃縮8個帶緣的測試管 每個聚四氟乙烯吸盤上承載的8個帶緣的測試管同時減壓。 且每次不能少于8個測試管。 在同等條件下混合所有的測試管,混合力能被連續地調節。 強大的傘狀偏心震蕩均勻混合8個測試管。
| ||||||||||||||||||||
技術規格: | ||||||||||||||||||||
|
Mycoplasma, the smallest and self-replicating prokaryotes, are common contaminant of primary and continuous cell line cultures. It has been shown that micoplasma contamination affects cell growth, morphology and metabolism. Because of their small size and flexibility, mycoplasma can pass through commonly used filters of 0.2 μm. Furthermore, unlike bacterial and fungi, micoplasma contamination is resistant to commonly used antibiotics, and not easy to be spotted visually. These drawbacks emphasize the need for regular screening in control of mycoplasma contamination. Conventional screening methods include microbiological culture, fluorescent DNA staining and biochemical detection methods. However, mycoplasma culture is restricted to specialized laboratories and takes 2-4 weeks. Results of DNA fluorochrome staining are difficult to interpret due to the presence of broken nuclei. Various biochemical detections are time consuming and often lack of sensitivity. Recently, polymerase chain reaction (PCR) based methods have been developed as a quick and convenient detection of low level mycoplasma infection, which offers great advantage over the conventional methods because of its extreme sensitivity and specificity. Computer alignment studies of mycoplasmal 16S rRNA sequences have revealed the existence of highly conserved sequences. Primers designed according to these sequences allow the specific amplification of mycoplasma DNA fragment and thus highly sensitive detection of mycoplasma. ScienCell™ Mycoplasma PCR Detection Kit is a 16S rRNA-based PCR assay including 2X reaction buffer, primer set, as well as internal amplification control (IAC) and positive sample control. The genus-specific primer set we select recognizes the five typical contaminating mycoplasma species (i.e. M. hyorhinis, M. arginini, M. orale, M. fermentans, and A. laidlawi), which account for 98% of contaminations, as well as members of the genera Ureaplasma, Spiroplasma, and Acholeplasma, which account for the remaining 2% of contaminations. Eukaryotic and bacterial DNA is not amplified by this kit. The IAC is designed to be co-amplified simultaneously with the target mycoplasma sequence by the same set of primers. The resulted control band, which is distinguished from the target band by a difference in molecular mass, indicates the occurrence of DNA amplification. Therefore, false negative results due to the presence of PCR inhibitors in some cell cultures can be identified. Our kit also provides a positive sample control, which is noninfectious genomic DNA (gDNA) of M. fermentans. On the other hand, a no template (i.e. DNA-free DI H2O) negative sample control can help to determine whether there is a false positive result due to carry-over contamination. Each experiment should include both positive and negative sample controls, as well as the IAC.Product Use
This assay kit is used to detect mycoplasma in vitro. It is for research use only. Not for use in animals, humans, or diagnostic procedures.